|
| |
| |
|
Induction Motors |
25 watt |
Frame Size : 80 x 80 mm |
Specifications : Continuous Rating, TE Aluminium Body |
| |
Rotates in clockwise or counter clockwise direction. Direction of rotation can be reversed Overruns for a few rotation after supply is cut off
Speeds are 2880 / 1440 RPM and further low speeds with gearbox
Terminal Box or open lead wires for connection |
|
|
|
| |
| |
Model |
Output Power |
Frequency |
Supply Voltage |
Current |
Starting
Torque |
Rated Torque |
Rated Speed |
Capacitor |
|
W |
Hz |
V |
A |
Kg.cm |
Kg.cm |
RPM |
μF |
80 IW 4G25 |
25 |
60 |
Single phase 110 V |
0.4 |
1.2 |
1.6 |
1450 |
2.5 |
80 IX 4G25 |
25 |
50 |
Single phase 230 V |
0.24 |
1.5 |
1.9 |
1250 |
1.5 |
80 IY 4G25 |
25 |
60 |
Three phase 230 V |
0.2 |
1.6 |
1.6 |
1450 |
. |
80 IY 4G25 |
25 |
50 |
Three phase 230 V |
0.2 |
1.6 |
1.9 |
1250 |
. |
90 IZ 4G25 |
25 |
50 |
Three phase 415 V |
0.12 |
1.6 |
1.9 |
1250 |
. |
|
| |
| |
Gearmotor Torque Table |
The maximum permissible torque is 80 Kg.cm. |
| |
|
Unit : kg.cm |
| |
RPM |
500 |
416 |
300 |
250 |
200 |
166 |
120 |
100 |
83 |
60 |
50 |
41 |
30 |
25 |
20 |
16 |
15 |
12.5 |
10 |
8.3 |
Gear Ratio |
3 |
3.6 |
5 |
6 |
7.5 |
9 |
12.5 |
15 |
18 |
25 |
30 |
36 |
50 |
60 |
75 |
90 |
100 |
120 |
150 |
180 |
Output Torque |
5 |
6 |
8 |
10 |
12 |
15 |
21 |
25 |
30 |
37 |
45 |
54 |
68 |
80 |
80 |
80 |
80 |
80 |
80 |
80 |
|
|
60 Hz |
Unit : kg.cm |
|
RPM |
600 |
500 |
360 |
300 |
240 |
200 |
144 |
120 |
100 |
72 |
60 |
50 |
36 |
30 |
24 |
20 |
18 |
15 |
12 |
10 |
Gear Ratio |
3 |
3.6 |
5 |
6 |
7.5 |
9 |
12.5 |
15 |
18 |
25 |
30 |
36 |
50 |
60 |
75 |
90 |
100 |
120 |
150 |
180 |
Output Torque |
4.1 |
5 |
6.9 |
8.3 |
10 |
12 |
17 |
21 |
25 |
31 |
37 |
45 |
56 |
67 |
80 |
80 |
80 |
80 |
80 |
80 |
|
| |
The Gearheads are sold seperately.
A Coloured background indicates gear shaft rotation in the same direction; a White background indicates rotation in the opposite direction as the motor shaft.
The Speed of Geared Motor is calculated by dividing the motor's synchronous speed ( 50 Hz: 1500RPM, 60 Hz: 1800RPM ) by the gear ratio.
The actual Speed is 2~20 % less than the displayed value, depending on the size of the load. Characteristics, specifications and dimensions are subject to change without notice.
|
|
|
|
| |
| |
|
| |
Dimensional Drawings |
| |
Dimensions
Motor, Gear Boxes with Terminal Box
|
|
| |
|
|
| |
|
Motor Round Shaft With Terminal Box
|
|
| |
|
|
|
| |
|
Motor Gear Boxes With Leadwires
|
|
| |
|
|
|
| |
|
|
| |
|
|
Weight |
Motor : 2.6 Kg. |
Gear Box : 1.5 Kg. |
|
|
|
| Wiring Diagram for Single Phase Motors |
|
|
Short Black wires and connect as shown
to rotate the motor in clockwise direction
To change the direction, flip SW to CCW |
|
Red wires are for running winding &
Black wires are for starting winding
To change the direction, interchange
Black wires or Red wires |
|
|
| |
| Wiring Diagram for Three Phase Motors |
|
|
To change the direction, interchange any two wires between U, V & W
For 415 Volt supply, wires are connected as
shown. Short White, Black & Blue wire and
then insulate properly. |
|
To change the direction, interchange
any two wires between U, V & W
For 230 Volt 3 Ph supply, wires are connected
as shown. |
|
|
| |
| Change the direction of the motor only after it stops rotating. If the attempt is made during rotation, motor may ignore the reversing command or change the direction after some time. |
|
| |
|
|
|
|
|
|
|
|
|
|