Specifications : 30 Minute Rating, TE Aluminium Body
Model
Output Power
Frequency
Supply Voltage
Current
Starting Torque
Rated Torque
Rated Speed
Capacitor
W
Hz
V
A
Kg.cm
Kg.cm
RPM
μF
65 RW2G12
12
60
Single phase 110V
0.3
0.27
0.4
2900
2.15
65 RX 4G12
12
50
Single phase 230V
0.18
0.27
0.5
1200
1.85
65 RX 2G12
12
60
Three phase 230 V
0.18
0.27
0.4
2500
1.0
65 RY 4G12
12
50
Three phase 230 V
0.12
0.3
0.4
1200
.
65 RZ 4G12
12
50
Three phase 415 V
0.1
0.3
0.4
1200
.
The two pole motor i.e. which runs at 2500 RPM at rated torque, is recommended for use
as it is more efficient than four pole motors.
There is no thermal protection to these motors.
Be sure to turn the motor off before inspection.
Gearmotor Torque Table
The permissible torque is 40 Kg.cm.
50 Hz : Two Pole Motor
Unit : kg.cm
RPM
1000
832
600
500
400
333
240
200
166
120
100
83
60
50
40
33
30
25
20
16
Gear Ratio
3
3.6
5
6
7.5
9
12.5
15
18
25
30
36
50
60
75
90
100
120
150
180
Output Torque
1.0
1.2
1.8
2.1
2.7
3.2
4.5
5.4
6.5
8
9.6
11.5
13
15.6
19.5
23
26
31.2
39
40
50 Hz : Four Pole Motor
Unit : kg.cm
RPM
500
416
300
250
200
166
120
100
83
60
50
41
30
25
20
16
15
13
10
8.3
Gear Ratio
3
3.6
5
6
7.5
9
12.5
15
18
25
30
36
50
60
75
90
100
120
150
180
Output Torque
1.2
1.4
2
2.4
3
3.6
5
6
7.1
8.9
11
13
16
19
24
29
32
36
38
40
The Gearheads are sold seperately.
A Coloured background indicates gear shaft rotation in the same direction; a White background
indicates rotation in the opposite direction as the motor shaft.
The Speed is calculated by dividing the motor's synchronous speed (Two pole motor :3000RPM,
Four pole motor :1500RPM ) by the gear ratio.
The actual Speed is 2~20 % less than the displayed value, depending on the size of the load.
Characteristics, specifications and dimensions are subject to change without notice.
Dimensional Drawings
Dimensions
Motor, GearBox with Terminal Box
Motor Round Shaft With Terminal Box
Motor GearBox With Leadwires
Key & Keyway
Weight
Motor : 1 Kg.
GearBox : 5 Kg.
Wiring Diagram -
Capacitor Cap Type
Single Phase
Three Phase
Capacitor is connected internally and is fitted in capacitor cap. Make the connections as shown to rotate the motor in clockwise direction.
To change the direction, flip SW to CCW
Make the connections as shown to rotate the motor in clockwise direction.
To change the direction, interchange any two wire between U, V & W
Lead Wires Type
Single Phase Motors
Make the connections as shown to rotate the motor in clockwise direction
To change the direction, flip SW to CCW
Short Black wires and connect as shown to rotate the motor in clockwise direction
To change the direction, flip SW to CCW
Red wires are for running winding & Black wires are for starting winding
To change the direction, interchange Black wires or Red wires
Three Phase Motors
To change the direction, interchange any two wires between U, V & W. For 415 Volt supply, wires are Red coloured
For 230 Volt supply, wires are White coloured
To change the direction, interchange any two wires between U, V & W For 415 Volt supply, wires are connected as
shown. Short White, Black & Blue wire and then insulate properly.
To change the direction, interchange any two wires between U, V & W. For 230 Volt 3 Ph supply, wires are connected
as shown.
Change the direction of the motor only after it stops rotating. If the attempt is made during rotation, motor may ignore the reversing command or change the direction after some time.
